Repairs to uPVC Windows

uPVC is a great choice for modern homes. They are long-lasting, durable and easy to maintain. They are not susceptible to rot or rust like aluminum or timber.

It is essential to clean and oil UPVC doors and uPVC repair windows regularly. This will reduce costly repairs and improve the efficiency of energy.

1. Broken Glass

The damaged glass in your windows can cause significant damage to your home and even be fatal. It is essential to take the time to ensure that you are doing everything you can to ensure that your windows are in good condition.

For single pane windows it is fairly easy to replace them, and the replacement is usually able to fit into the old frame very easily. If you have double-paned windows which are joined by internal beading, it is harder to remove and replace the panes that were previously in use. In this case you'll need to locate some plastic spacers to help the new pane to fit perfectly into the window frame.

If you are going to attempt to remove the window panes yourself it is important to wear the proper safety gear, including thick gloves and uPVC repair eye protection. It is also a good idea to lay down a drop cloth before you begin working on the glass, so that any fragments of glass fall onto the fabric instead of onto the floor, where they could be trodden under and cause further damage.

Once the glass has been removed from the window, it's best to seal the gap with some clear packaging tape or duct tape to block water and drafts from entering the home until a professional is able to come out and fix the window. This will also act as a barrier, preventing any intruders to gain access into your home. If the gap is large, you may be interested in a security door that has an integrated window, since it will provide the best of both worlds.

2. Sagging

Upvc windows and doors are a low-cost energy-efficient, durable and long-lasting alternative to timber windows made of sash. However, over time they are susceptible to a range of problems including sliding. A sagging window can cause problems with light, draughts and even security. It's important to take action when you realize that your Upvc Repair [Tntech.Kr] windows are sliding.

Repositioning the hinges can aid in fixing a window which is sliding. To do this, you'll need open the window so that you can access the frame. You can then unscrew both the hinges at the top and bottom using a screwdriver and adjust them counter-clockwise or clockwise. Once you've repositioned the hinges, shut your window and verify the fitting. If you're satisfied with the fit, tighten the screws to ensure they remain in the right place.

If you are unable to move the hinges, you might have to replace the seal. Over time rubber seals can lose their elasticity and dry out which causes them to lose tightness. If this happens, it's important to replace the seal as quickly as possible so that your uPVC windows remain watertight and secure from draughts.

uPVC handles can also loosen up. Most often it is due to screws that have become loose over time. However, it can also happen because the handle mechanism has been worn out. Luckily, it's not difficult to fix the handle of a window that is loose yourself. First, you'll need close the window and then perform an initial test fit. The joint at the corners of the sash should be aligned with the joint on the casing. If it isn't then you can make use of a screwdriver to loosen the handle and then reverse the mechanism back into position.

3. Water Leaks

If you're waking up to damp floors and mouldy walls every time it rains it's important to take action. Water leaks through windows can cause structural damage to your home and also affect your ability to regulate the temperature inside your home. The most common cause for leaks in uPVC windows is that the sealant surrounding the frame is either damaged or missing.

This is a fairly simple fix that can be completed by any competent DIYer. Based on the severity of the issue the caulking that was used up may require removal before a new layer of caulk can be put on. It is essential to remember that when it comes to uPVC window repairs, do avoid the temptation to "over-caulk' as this will only make the area more difficult to clean and reduce your energy efficiency.

Verify that the drainage holes have no debris in them, and also that the sill pan is properly angled to drain away from the window. In more serious instances, you may need to think about replacing the window.

Other signs of long-term water leakage are decayed sills and the appearance of black spots of mold on the wall near the window. This mold thrives in damp environments and can quickly spread throughout the home.

It is also important to keep in mind that if the leakage is coming from between the glass of your double glazed windows it may be more likely to be an issue with the glass seal, rather than the frame or sliding. A uPVC specialist can easily fix this problem by replacing the glass seal. This will ensure the complete insulation of your windows.

4. Faulty Hinges

If your uPVC windows are brittle to open, or slack and blow open in a breeze It could be hinges at fault. These are easily repaired by any DIYer who is skilled and can be completed in a matter of minutes.

Most households in the UK will have top-hung or side hung uPVC windows that use hinges and, just like any mechanical component they can wear down over time. It's very simple to change the hinges on a window but it's much easier if someone helps you hold the frame.

It is also worth checking that the uPVC hinges are opening and closed in the right direction. This can be done by looking for the arrow on each hinge, this indicates the direction in which the window should open.

Faulty window hinges could be caused by improperly opening the window a certain way or by improper installation in the factory. This can often be resolved by sending us a picture on our website. We will be pleased to offer you suggestions.

Regularly lubricating the hinges is also necessary. Applying a light engineering lubricant to the hinges is an ideal way to do this. We suggest using the lubricant that doesn't contain solvents, like 3-in-1 Multi-Purpose oil. Regular lubrication will make the window easier to open and close. It can also lower the risk of a window sticking and help prevent corrosion. It is recommended to do this once a year. WD40 or other solvent-based lubricants should not be used since they can damage your uPVC windows.

5. Draughts

Draughts in upvc windows can be caused by a few various factors. The hinges may also become misaligned due to wear, causing gaps where the sash meets frame. If they are damaged beyond repair, it might be necessary to get them re-aligned. The interlock, which is on the hinge side of the window, may be misaligned. Again, it is possible to give them a good clean, but in some cases it might be necessary to get them replaced.

These seals can wear down or get damaged over time, allowing air escape. This can be prevented by replacing them with high-quality weatherstripping. Another alternative is to replace the window with low-emissivity glass. this will help in regulating indoor temperatures and will reduce the possibility of draughts.

The final method to cut down on drafts effectively is to use a draught-excluder. These are usually made of fabric tubes filled with a filler which can be placed over your window doctor sill. They can keep your home warm by blocking out cold air.

With a little regular maintenance and repair, your upvc windows will provide an excellent level of security and insulation for your home. It is crucial to realize that all windows have a lifespan and there may come the point when it's more economical to replace them than fix them. If you are experiencing issues with your Upvc windows, it's best to seek professional assistance as soon as you can.