Repairs to uPVC Windows

uPVC is an excellent choice for modern homes. They are long-lasting, durable and easy to maintain. They don't decay or rust as timber and aluminum.

It is important to clean and oil UPVC doors and windows regularly. This will save you from costly repairs and improve the efficiency of energy.

1. Broken Glass

The damaged glass in your windows can cause significant damage to your home and even be fatal. It is essential to ensure that your windows are in good condition.

For single pane windows, it can be relatively simple to replace them, and the replacement will usually fit inside the frame that was previously installed easily. If you have double-paned windows that are joined by internal beading, it is difficult to remove and replace the old panes. In this situation it is essential to purchase plastic spacers to aid in fitting the new pane into the window frame.

If you plan to try to remove the glass panes yourself it is important to wear the proper safety gear such as gloves that are thick and protective eyewear. It is also a good idea to lay down a drop cloth prior to when you begin working on the glass to ensure that any shards fall onto the fabric instead of onto the floor where they could be trodden under and cause further damage.

Once the glass has been removed, it's a good idea to seal the gap with some clear packaging tape or duct tape to block water and drafts from getting into the property until a professional comes out and repair the window. This will also act as a barrier, deterring any intruders to gain access to your home. If the distance between the window and UPVC repair the door is substantial, you may prefer security screens that has windows. This will provide the best of both.

2. Sagging

uPVC windows and doors are a cost-effective energy efficient, durable and long-lasting alternative to timber sash windows. However, over time, they may be afflicted by a variety of issues, including sliding. A sagging uPVC window could cause issues with light, draughts and even security. If you find that your uPVC window is beginning to lose its shape, it's crucial to act fast to prevent the problem from becoming worse.

Repositioning the hinges could aid in fixing a window that is sliding. First, you'll need to open the windows so you can access the frame. With an screwdriver, take off the top and bottom hinges and adjust them by turning them clockwise or counter-clockwise. Close your window to check the fit after having relocated your hinges. If you're happy with the fit, tighten the screws to ensure that they remain in the right place.

If you can't reposition the hinges, you might require replacing the seal. Rubber seals can dry out and lose their elasticity over time, leading them to lose their tightness. It is crucial to replace your seal as soon as you can in order to keep your upvc repair - just click the next post, window watertight and draughtproof.

uPVC handles may also become loose. Often, this is caused by screws that have become loose over time. However, it could occur because the handle mechanism has been worn out. Luckily, it's not difficult to fix the handle of a window that is loose yourself. First, you'll need to close your window and do an initial test to ensure that it fits. The joint at the corners of the sash should be aligned with the joint on the casing. If it isn't then you can use a screwdriver or a wrench to loosen the handle, and then reverse the mechanism back into position.

3. Water Leaks

If you wake up to wet floors and mouldy walls every time it rains it's crucial to take action. Water leaks from windows are not just a cause for degradation of your home's structure but also hamper your efforts to control the temperature within your home. Most of the time, uPVC window leaks are caused by a lack or damage to the sealant.

This is a fairly simple fix that can be done by any DIY expert. Depending on the severity of the issue is, old caulking may need to be removed. It is important to keep in mind that when it comes to uPVC window repairs you should avoid the temptation to "over-caulk and then make the area harder to clean and could reduce your energy efficiency.

It is important to check that any drainage holes are free of debris and that the sill pan has been angled properly so that it drains away from the window. In more extreme instances, you may need to replace the window.

Mold spots and rotten sills are other signs of water leakage. This fungus thrives in damp conditions and is able to quickly spread throughout the home.

It is also important to remember that if the leak is coming from between the glass of your double glazed windows it may be more likely to be an issue with the glass seal, rather than the frame or sliding. A uPVC specialist can fix this issue by replacing the glass seal. This will ensure the complete insulation of your windows.

4. Faulty Hinges

If your uPVC windows are brittle to open, or are loose and open in a breeze, it may be the hinges that are at fault. These are easily replaced by any competent DIYer and can be done within a few minutes.

Like any mechanical part hinges are prone to wear out over time. It's easy to change a window hinge, but it's easier if someone else helps hold the frame.

It is also important to ensure that the uPVC hinges are opening and closed in the correct direction. This can be done by checking for the arrows on each hinge, this indicates which way the window should open.

The issue could be caused either by opening the window incorrectly or due to a poor installation in the factory. Sending us a picture via our website is often enough to resolve the problem. We are more than happy to provide advice.

It is also crucial to ensure that the hinges are lubricated regularly. This can be done by applying a light engineering oil to the hinges. We suggest using a solvent-free lubricant such as the 3-in-one Multi-Purpose oil. Regularly lubrication makes the window easier to open and close. It also helps prevent corrosion and decrease the chance of sticking. Ideally, you should perform this every year. WD40 and other solvent based oils are not recommended because they can damage the parts of your uPVC window.

5. Draughts

Draughts in windows made of upvc can be caused by a few different things. Firstly the hinges, again due to wear and tear may become displaced, which will cause a gap to form where the sash joins the frame. If they are beyond repair, it could be required to realign them. In addition, the interlock could be disaligned. It is located on the hinge's side, and may need to be cleaned. In some instances it might be necessary to replace them.

These seals are susceptible to wear and tear or get damaged over time, allowing air escape. This can be avoided by replacing them with high-quality weatherstripping. Replace the upvc windows with low-emissivity glass. This will help regulate indoor temperatures, and reduce the possibility of draughts.

Lastly, one of the most effective ways to reduce draughts is by using a draught excluder, these are typically fabric tubes filled with some kind of filler. They can be put on top of your windowsill. They will keep your home warm by blocking cold air.

With a little regular maintenance and repair, your upvc windows will continue to provide a great level of security and insulation for your home. However, it is important to realize that all windows have a life span and they may reach a point where it is more efficient to replace them than repair them. So, if you're experiencing problems with your upvc windows, it's best to seek professional assistance immediately.